Operating procedures of drifting fish feed equipment

 1.  Running procedures of  drifting fish feed  equipment

( 1) Precautions before  beginning and after stopping

①  Inspect all parts of fish feed  drifting pellet making  equipment,  particularly the connecting screws  as well as anchor bolts of each section of the puffing chamber, the  attaching bolts  in between the motor base  and also the frame, and the bolt connection between the puffing chamber  as well as the  structure, and there must be no looseness;

Related post: 8-10T/H Fish Feed Mill

② Manually  revolve the main shaft,  right now, there  ought to be no  massaging  noise in the fish feed  drifting pellet making  maker puffing  dental caries;

③  Beginning the feeding auger of fish feed  drifting pellet making  equipment,  examine its stepless high-speed  efficiency,  and also  call for  regular operation;

④ Check  as well as clean the water  and also gas  courses before  beginning the fish feed floating pellet making  maker, and all filters  require to be  cleansed;

⑤  Prior to starting the fish feed floating pellet making machine,  inspect whether the  electrical wiring of the electric control  component is  proper, whether the  turning of each motor is  proper,  as well as whether the control is  dependable;

Related post: https://www.richipelletmachine.com/fish-feed-mill/

⑥ After the fish feed floating pellet making  equipment is stopped, you must  put on high-temperature  handwear covers,  rapidly  eliminate the discharge mold,  and also immediately  tidy it while it is  warm,  as well as start the  primary  electric motor to empty the  product  collected in the  blowing  tooth cavity. When the corn is  blown, soybean powder should be  included The material is rinsed clean;

⑦  Take notice of  safety and security when  dumping the machine,  and also do not stand in front of the machine to  prevent  threat  triggered by residual pressure in the fish feed floating pellet making  maker  dental caries;

⑧ After the fish feed floating pellet making machine is running  typically, it shall not be  closed down at will.

Related post: Fish Feed Production Plant

( 2) Power on

① Before  beginning the fish feed floating pellet making  equipment,  inspect the  bolts, and there  need to be no looseness;

②  Make certain the  regular supply of steam  as well as water;

③ Ensure that the power supply  and also  electric  devices are normal;

④  Open up the  heavy steam valve,  pre-heat the floating fish pellet machine  blowing chamber, the  temperature level  has to do with 100  levels;

⑤  Begin the fish feed  drifting pellet making  equipment: start the conditioner, start the feeding auger, when there is  product flowing out from the  electrical outlet of the conditioner, start  including  heavy steam to the conditioner.

A small amount of water is  included, and the  product is fed  right into the puffing cavity at the same time. After the  product is extruded by fish feed floating pellet making  maker, the puffing  result  as well as  wetness of the product are adjusted.

Related post: Sinking Fish Feed Machine

( 3) Downtime

After the fish feed  drifting pellet making  equipment  manufacturing comes to an end, it needs to be stopped. The  quit  series is: feeding auger  and also conditioner.  After that wait  till the  suggested value of the main engine current on the electric control  cupboard becomes the no-load current  worth, then stop the  primary motor and the oil pump  electric motor.

( When the corn is  blown,  regarding 25 kg of soybeans  ought to be fed into the bypass feeding port of the  initial  area of the puffing  dental caries. To  cleanse the  recurring corn  product in the puffing  dental caries,  and after that  quit the main motor  to stop the fish feed floating pellet making  maker from  obstructing),  after that  promptly  dismantle the puffing  tooth cavity of the tail  area for  cleansing.

After  cleansing,  use grease to the  internal wall of the  primary shaft and screw head (After feeding grease), re-install it and wait for the  following boot;

When you see that the  product  degree  indication on the silo indicates that the  product level has  gotten to  the most affordable level, start to  get ready for shutdown.  Currently, do not  quit the feeding auger  and also conditioner,  and also stop feeding when the  major fish feed  drifting pellet making  device  existing  decreases to the no-load current auger and conditioner.

Related post: Shrimp Feed Mill

2. Operation sequence of floating fish feed machine

( 1 )When  blowing soybeans,  both  areas at the inlet end of the  blowing cavity are single screw heads, and the three  areas at the outlet end are equipped with  dual screw heads.

First, add steam to the  coat to  pre-heat the  blowing  tooth cavity to about 100  levels,  and also  placed the screws on the  blowing  dental caries at the tail section. After the plug is  tightened up, loosen it for 3-4 turns, and then  tighten up the screw plug to  take care of the screw plug  prior to feeding.

By  managing the stepless high-speed mechanism of the feeding auger, the feeding speed is from slow to  quickly,  as well as the feeding speed is from small to  huge. After the soybean meal is  expelled from the screw plug hole,  include the cover to  get in the  regular  manufacturing,  and also configure the screw  connects with  various apertures to  acquire soybean  dish with  various  returns and finenesses.

By configuring the  conelike pressure rings of different diameters, the  shown temperature of the four-section (discharge end)  blowing  dental caries is 130-140  levels. It is recommended that the  screen of the crusher used for crushing soybeans  ought to have a diameter of 3-4.

Related post: 6-7T/H Fish Feed Plant

( 2 )When  squeezing out powdery feed by fish feed  drifting pellet making  equipment, the  squeezing out screws in the extruding  tooth cavity are all single screw heads,  include  vapor to the  coat to preheat the  blowing  tooth cavity to  regarding 80  levels,  as well as  go into the fish feed  drifting pellet making  equipment  and also  heavy steam  consistently  satiated  as well as  solidified powder.

 Regarding 18%, this  need to be  performed in the feed conditioner,  and also the feed amount is controlled by the stepless speed regulating  system from small to large. Note that the  analysis of the ammeter of the  major motor  must not exceed the  ranked  present of the  primary engine of fish feed floating pellet making  device.

 Be careful of  straining the  electric motor  as well as  squeezing out  fine-grained  products. When the temperature of the  squeezing out chamber at the discharge end is  managed to an  proper  level by configuring  conelike pressure rings with  various  sizes.

The above is the principle, structure and  running procedures of the fish feed floating pellet making  device introduced by Richi Machinery. In  search of  crunchy taste  and also  great  look,  producers  usually  include a  raising agent (or baking powder), which  consists of a  particular  quantity of aluminum elements,  and also generates gas when heated  throughout  cooking or frying,  as well as the  raising agent is inside the food.

For details please contact: Richi Machinery 

WhatsApp：86 138 3838 9622

Email：enquiry@richipelletmachine.com